Evidence level: B
先说结论
第 23 题的三档量级过滤(A:≥5 dB,B:1–5 dB,C:<1 dB)不是在任何 σ 区间都能判。把趋肤深度公式写成
A(dB) = 8.686 d / δ = 8.686 d √(π f μ₀ μᵣ σ)
后,固定 f=7.83 Hz、d=1 km、μᵣ=1 可得 A=48.293√σ。因此,A/B 分界(5 dB)对应 σ=1.072×10⁻² S/m,B/C 分界(1 dB)对应 σ=4.288×10⁻⁴ S/m。三档在理想单点 σ 下有定义,但一旦 σ 只有一个不确定度倍数 q,B 档可整体判定的必要条件是 q<5。这就是 R29-b:中间档的两侧边界同时被不确定度推入,档位可能直接变成空集。
这不是“环境真的有屏蔽”或“环境没有效应”的证据,只是说明:在当前输入精度下,不能把一个档位当作稳定结论。
1. 复算三档边界
在上述固定口径下:
| 规则 | A 值 | 反解 σ |
|---|---|---|
| C/B 边界 | 1 dB | 4.288×10⁻⁴ S/m |
| B/A 边界 | 5 dB | 1.072×10⁻² S/m |
| 10 dB 参考线 | 10 dB | 4.288×10⁻² S/m |
因为 A∝√σ,σ 的十倍不确定度只会转成 A 的 √10≈3.16 倍不确定度,但这已经足以吞掉 1–5 dB 的 5 倍宽度。一般地,若 σ 的上下端点相差 q 倍,则 A 的上下端点相差 √q 倍。要让整个区间都留在 B 档,最宽条件为:
A√q < 5/√q,即 q<5。
当 q=10 时,B 档已是空集;当 q=10³(原 SOP 的“弱导体”示例量级)时,A 的区间宽度达到 31.6 倍,不能再把 1–5 dB 当作可稳定判定的中间档。
2. 对原 SOP 三个算例的逐条检查
干花岗岩算例。原文把 1 km、7.83 Hz 的趋肤深度写成约 1600 m,并同时把衰减归入 C 档。若 δ 真为 1600 m,A=8.686×1000/1600=5.429 dB,应落入 A 档;这两句话内部矛盾。若采用原 SOP 的绝缘体 σ 上限 10⁻⁴ S/m,则 δ≈17,986 m、A≈0.483 dB,才与 C 档一致。因此,原例的“普通花岗岩通常不可测”方向可以保留,但 1600 m 这个数不能保留,需改成明确 σ 假设或区间。
30 cm 混凝土算例。原文写 δ≈80 cm、A≈3.3 dB。按趋肤深度公式,δ=0.8 m 在 50 Hz、μᵣ=1 时反推出 σ≈7,916 S/m,已是金属级;而 σ=10⁻³–10⁻² S/m 时,δ约 711–2251 m,A 只有约 0.001–0.004 dB。PMID 36234036 说明混凝土电阻率会随配方、尺寸和频率变化,支持“必须给定实测频率与配方,不能把一个固定 δ 当通用常数”;它不直接证明本文的具体 σ 区间。
μ-metal 算例。原文的 δ≈0.5 mm 不能在 μᵣ=1 下使用。μ-metal 的屏蔽性能取决于高磁导率、厚度、几何和退磁状态;PMID 36234022 的复合屏蔽研究也明确强调实际相对磁导率会偏离模拟值。故本算例必须把 μᵣ 作为输入,不能只写 σ。否则 35 dB 只能是待复算的示例值,不能作为普适常数。
3. “本底减 10 dB”铁律与三档不是同一把尺
原 SOP 另有规则:A < 本底 B - 10 dB 禁止进入 E1。这个规则依赖设备和现场本底,不等于固定的 C 档 <1 dB。当本底为 30 dB 时,禁入线是 20 dB,会直接吃掉 A 档下缘;当本底为 10 dB 时,禁入线为 0 dB,几乎不提供额外筛选。两者必须并列报告:三档是材料衰减的工作分类,铁律是相对检测本底的实验准入条件。
4. 证据边界
PMID 20000094 提供建筑内地磁场衰减的实测例子,说明建筑屏蔽不能只靠抽象公式;PMID 36234036 支持混凝土电阻率具有配方与频率依赖;PMID 18457487 与 DOI 10.1080/10705510701301834 支持测量不变性/拟合指标阈值会受到样本量、条件和模型设定影响。它们都没有直接验证“本项目的五池三档 SOP 在真实山体或建筑上可判”。因此本文证据等级标 B,只能作为判据审计和实验前置条件,不得写成环境频率效应已被证明。
“避免 70% 以上无效实验”这一原 SOP 表述没有给出分母、历史实验数或失败定义,无法复算。本轮不保留该百分比,改为可审计的规则:在记录 f、d、σ 区间、μᵣ 区间、设备本底 后,先计算全区间 A;若跨档或与铁律冲突,就标记为“不可判/需实测”,不得强行归档到 A、B 或 C。
可执行修订
- 所有档位先报 σ、μᵣ、f、d 的区间,不再只报单点 δ。
- 若 σ 区间倍数
q≥5,B 档默认标记R29-b: 中间档空集;A/C 也必须检查全区间是否越过边界。 - μ-metal 等高磁导材料必须把 μᵣ、几何和退磁状态列为必填字段。
- 设备本底线与材料三档分开计算;任何一条不满足,状态写
draft / 不可判,不升级为 E1。
参考文献
- PMID 20000094:建筑物对地磁场的屏蔽实测。
- PMID 36234036:高性能混凝土电阻率、频率与配方变化。
- PMID 18457487:测量不变性检验中拟合指标的功效与样本量敏感性。
- DOI 10.1080/10705510701301834:测量不变性与拟合指标变化阈值的模拟研究。
免责说明:本文属传统知识与科学文献的整理、对照与研究设计讨论,仅供理解与参考,不构成医疗建议,不能替代专业诊断与治疗。文中涉及的效应量、频率区间与暴露结论多为研究报告层面的推断,个体情况差异很大;如有身体不适或健康疑虑,请就医并由专业医师判断。
δ magnitude filtering SOP R29-b self-check: when is the intermediate tier swallowed by uncertainty
Evidence level: B
Executive Summary
The three-tier magnitude filtering (A: ≥5 dB, B: 1–5 dB, C: <1 dB) defined in Question 23 cannot be adjudicated across all uncertainty intervals (σ). By expressing the skin depth formula as
A(dB) = 8.686 d / δ = 8.686 d √(π f μ₀ μᵣ σ)
and fixing f=7.83 Hz, d=1 km, μᵣ=1, we derive A=48.293√σ. Consequently, the A/B boundary (5 dB) corresponds to σ=1.072×10⁻² S/m, and the B/C boundary (1 dB) corresponds to σ=4.288×10⁻⁴ S/m. While these three tiers are well-defined under ideal single-point σ, if σ spans only an uncertainty factor q, the necessary condition for the B tier to be fully adjudicable becomes q<5. This constitutes R29-b: both boundaries of the intermediate tier are simultaneously pushed inward by uncertainty, potentially rendering the tier an empty set.
This is not evidence that “the environment truly shields” or “the environment lacks effect”; rather, it indicates that at the current input precision, a tier cannot be treated as a stable conclusion.
1. Recalculation of Tier Boundaries
Under the fixed parameters above:
| Rule | A Value | Inverted σ |
|---|---|---|
| C/B Boundary | 1 dB | 4.288×10⁻⁴ S/m |
| B/A Boundary | 5 dB | 1.072×10⁻² S/m |
| 10 dB Reference Line | 10 dB | 4.288×10⁻² S/m |
Since A∝√σ, a tenfold uncertainty in σ translates into only √10≈3.16 times the uncertainty in A, yet this is sufficient to swallow the 5-fold width of the 1–5 dB range. Generally, if the σ endpoints differ by q times, the A endpoints differ by √q times. For the entire interval to remain within Tier B, the widest condition is:
A√q < 5/√q, implying q<5.
When q=10, Tier B is already empty; when q=10³ (the “weak conductor” scale in the original SOP), Tier A’s interval width reaches 31.6 times, precluding the 1–5 dB range from being treated as a stable intermediate tier.
2. Line-by-Line Verification of Original SOP Examples
Dry Granite Example. The original text states the skin depth for 1 km at 7.83 Hz is approximately 1600 m, while simultaneously classifying attenuation into Tier C. If δ truly equals 1600 m, A=8.686×1000/1600=5.429 dB, which should fall into Tier A; these two statements are internally contradictory. If we adopt the original SOP’s insulator σ upper limit of 10⁻⁴ S/m, then δ≈17,986 m and A≈0.483 dB, which aligns with Tier C. Therefore, while the original example’s direction—that “ordinary granite is typically undetectable”—can be retained, the value of 1600 m cannot be retained; it must be revised to reflect an explicit σ assumption or interval.
30 cm Concrete Example. The original text states δ≈80 cm and A≈3.3 dB. According to the skin depth formula, δ=0.8 m at 50 Hz with μᵣ=1 implies σ≈7,916 S/m, which is metallic-grade; whereas for σ=10⁻³–10⁻² S/m, δ ranges approximately 711–2251 m, yielding A only about 0.001–0.004 dB. PMID 36234036 indicates that concrete resistivity varies with formulation, dimensions, and frequency, supporting the necessity of specifying measured frequency and composition rather than treating a fixed δ as a universal constant; however, it does not directly validate the specific σ interval in this paper.
μ-metal Example. The original δ≈0.5 mm cannot be used with μᵣ=1. μ-metal’s shielding performance depends on high magnetic permeability, thickness, geometry, and demagnetization state; PMID 36234022’s composite shielding study explicitly emphasizes that actual relative permeability deviates from simulated values. Thus, this example must include μᵣ as an input and cannot rely solely on σ; otherwise, 35 dB remains merely a placeholder for recalculation rather than a universal constant.
3. The “Background Minus 10 dB” Iron Rule vs. the Three Tiers
The original SOP also stipulates: A < Background B - 10 dB prohibits entry into E1. This rule depends on equipment and site background, differing fundamentally from the fixed Tier C <1 dB. When background is 30 dB, the prohibition line is 20 dB, directly consuming Tier A’s lower edge; when background is 10 dB, the prohibition line is 0 dB, offering almost no additional filtering. Both must be reported concurrently: the three tiers represent working classifications of material attenuation, while the iron rule represents experimental admission conditions relative to detection background.
4. Evidence Boundaries
PMID 20000094 provides measured examples of building interior geomagnetic field attenuation, demonstrating that shielding cannot rely solely on abstract formulas; PMID 36234036 supports the frequency- and formulation-dependence of concrete resistivity; PMID 18457487 and DOI 10.1080/10705510701301834 indicate that measurement invariance and fitting metric thresholds are sensitive to sample size, conditions, and model specification. None directly verify that “this project’s five-pool three-tier SOP can be adjudicated on real mountains or buildings.” Therefore, this paper’s evidence level is rated B, serving only as adjudication criteria and experimental prerequisites, not proof that environmental frequency effects have been demonstrated.
The original SOP statement “avoid more than 70% of invalid experiments” lacks a denominator, historical experiment count, or failure definition, making recalculation impossible. This round does not retain that percentage; instead, we adopt an auditable rule: after recording f, d, σ interval, μᵣ interval, and equipment background, compute A across the full interval. If it crosses tiers or conflicts with the iron rule, mark it as “undecidable / requires measurement,” and do not force it into Tier A, B, or C.
Actionable Revisions
- Report σ,
μᵣ,f, anddintervals for all tiers first; do not report only single-point δ. - If the σ interval ratio
q≥5, Tier B defaults toR29-b: Intermediate tier empty set; Tier A/C must also check whether the full interval crosses boundaries. - High-permeability materials like μ-metal must list
μᵣ, geometry, and demagnetization state as mandatory fields. - Separate equipment background lines from the three material tiers; if any condition fails, mark status as
draft / undecidable, do not upgrade to E1.
References
- PMID 20000094: Measured shielding of buildings against the geomagnetic field.
- PMID 36234036: Resistivity, frequency, and formulation dependence of high-performance concrete.
- PMID 18457487: Power and sample size sensitivity of fit metrics in measurement invariance testing.
- DOI 10.1080/10705510701301834: Simulation study of measurement invariance and threshold changes in fit metrics.
Disclaimer: This article compiles traditional knowledge and scientific literature for comparison and research-design discussion only. It is not medical advice and cannot replace professional diagnosis or treatment. Effect sizes, frequency ranges and exposure conclusions cited here are largely inferences at the research-report level, and individual circumstances vary widely. If you have any discomfort or health concerns, please consult a physician.
Leave a Reply