靠山 ELF 屏蔽山体样本优先级重排 · σ 预筛 SOP

Written by

in

Language

Evidence level: C

目的:在进入 #14 阶段 3 跨断面 MT 实测前,先用岩体电导率 σ 把候选山体分成三档,避免在”ELF 透明地形”上空跑。
范围:本 SOP 只覆盖”靠山地形 1–30 Hz ELF 屏蔽测量”的山体样本筛选;不延伸到电磁辐射生物效应;不替代跨断面 MT 测点选址的工程细则。
证据层级:C(工程公式 + 文献 σ 区间 + 五池 #16 δ 表类比),不进入生物效应层。


一、为什么必须预筛

第 23 轮负结果合成(mountain-elf-typical-granite-transparent.md)给出 7.83 Hz 单点估算:

山体材料 σ (S/m) δ(7.83 Hz) 1 km 山体 A(dB)
普通花岗岩(干) 10⁻⁸–10⁻⁴ 数百米–数千米 ≈ 0.27 dB(远低于 Schumann 本底波动 ±1–3 dB)
湿花岗岩(含水/含矿) 10⁻³–10⁻¹ 几十米–几百米 1–10 dB 量级
湿玄武岩 10⁻²–10⁰ 几米–几十米 数十 dB 量级

核心结论:普通花岗岩山体对 7.83 Hz ELF 几乎透明(A(dB) < 1 dB);测量后大概率拿到”零结果”,无法证伪靠山 ELF 屏蔽假说。先做 σ 预筛,可把有限的人力/仪器成本压到最有判别力的样本上。

声明:本表来自 #16 δ 表 + #23 负结果合成;不依赖本轮新增文献。


二、三档样本优先级

把候选靠山地形按 σ 预筛分成三档(按 10 g 岩石样品实测 σ 决定分档,不依赖地质图/卫星图/民间命名):

档位 山体类型 σ (S/m) 1 km A(dB) @ 7.83 Hz 测量价值 建议
A 档(优先测) 湿玄武岩、含金属硫化矿/磁铁矿山体、断裂带蚀变岩 ≥ 10⁻² ≥ 10 dB 高(有能力证伪 H1 强屏蔽) 第一批测点
B 档(条件性测) 含水/含裂隙花岗岩、含黏土断层带、含盐水侵染灰岩 10⁻³–10⁻¹ 1–10 dB 中(验证 H0/H1 边界) A 档测完仍有预算再上
C 档(不测或仅作对照) 干燥未蚀变花岗岩、火成岩体外缘、未风化致密基岩 ≤ 10⁻⁴ < 1 dB 极低(按公式透明) 跳过,除非作为”零对照”基线

核心理由:A(dB) < 1 dB 的样本在 PSG/EEG 信噪比(30–50 dB)下完全无法区分;C 档测量拿不到可发表数据,浪费仪器时间。


三、σ 预筛的具体做法

3.1 桌面预筛(不上山)

  1. 地质图 + 遥感:用 1:5 万或 1:20 万区域地质图圈出靠山地形;优先选岩性标识为玄武岩、辉绿岩、磁铁矿、含矿花岗岩、断裂破碎带、温泉/地热出露区的山体。
  2. MT 公开数据反查:通过 IRIS/EMAGE、EarthScope、USArray MT 站点反查测点附近 0.001–10 Hz 大地电阻率(ρ = 1/σ);若已有 1–10 Hz 实测 ρ ≤ 100 Ω·m(即 σ ≥ 10⁻² S/m),直接判 A 档。
  3. 水文地质档案:当地水利/地热/矿权公开资料;存在地热井、温泉、含水层、矿体的,σ 偏高一档。

3.2 现场预筛(上山前必做)

  1. 取 10 g 岩石粉末 + 蒸馏水做泥浆电导率初测:用便携 EC 计(HANNA HI98311 等)测泥浆电导率,> 2000 µS/cm 提示 σ 偏高(> 10⁻³ S/m 数量级),A/B 档候选;< 200 µS/cm 大概率 C 档。
  2. 手持磁化率仪(KT-10 / SM-30)测磁化率:含磁铁矿/磁黄铁矿的岩体 χ > 1000×10⁻⁵ SI,A 档强信号;χ < 50×10⁻⁵ SI 多为普通花岗岩/砂岩,C 档信号。
  3. 简易四极法小剖面:用 4 根不锈钢电极 + 1.5 V 电池 + 万用表做 0.5 m Wenner 阵列,电流 I、电压 V,求 ρ = 2πa·V/I;与已知花岗岩 ρ 数量级(10³–10⁵ Ω·m)比对,偏低 ≥1 数量级即上调一档。

3.3 σ 不确定性的容差处理

岩石电导率受温度、含水率、孔隙率、频段影响,至少 ±1 个数量级(文献区间值即此含义)。预筛判档时采用”下限原则”:

  • 桌面预筛得 A 档下限(如 σ ≥ 10⁻² S/m),按本档执行;
  • 处于档位边界(10⁻⁴–10⁻³ S/m 之间)的样本,升级到上一档优先测,避免漏测;
  • 任何档位判定的”最低期望 A(dB)”都应 > 3 dB,否则降档。

四、与现有课题的衔接

现有课题 衔接方式
#14 靠山 ELF 屏蔽系数实测 阶段 3 跨断面 MT 测点选址前先走本 SOP,输出”三档候选山体清单”作为选址输入
#15 建筑-山体地形衰减类比 阶段 2-3 不必延伸到普通花岗岩(C 档);只对接 A/B 档的 σ 数据做类比校验
#16 δ 表 σ/μr 区间 本 SOP 的分档阈值即 #16 表的 A 档(10⁻²)、B 档(10⁻³)、C 档(10⁻⁴)三档具体化
#17 Schumann 山体 FEM FEM 候选测点改为湿玄武岩(A 档),普通花岗岩 FEM 跳过
#18 Schumann 山区 vs 平原文献基线 🛑 仍暂搁;解封后,本 SOP 的站名锚定(USArray MT、EarthScope、IRIS 站)可作文献回填的间接锚点

五、证伪与降级预案

失败情形 判据 处置
A 档山体 σ 实测 < 10⁻³ S/m 桌面/现场预筛判错 改 B 档测点或加测
A 档山体实测 A(dB) < 3 dB 假说 H1 弱屏蔽不成立 写”负结果+白皮书”,合并到龙脉规程附录
A 档山体实测 A(dB) ≥ 5 dB H1 强屏蔽成立 锁 #14 H1a;进入 #15 类比验证
A/B/C 三档 σ 实测无显著差异 预筛无效 升级为”穷举对照”模式,所有档位都测

六、证据与局限

  • 支持文献:干花岗岩 σ 区间 10⁻⁸–10⁻⁴ S/m 与频响依赖(ResearchGate 238536200);干玄武岩熔体 σ ≈ 1–10 S/m(PMC 12906345)。两文献合并后给出的 σ 跨 4–5 数量级差距,是本 SOP 分档的事实基础。
  • 未触及:生物效应、Schumann 节点偏移、人体 PSG/EEG 响应;这些由 #17、#18、池 ③ 单独处理。
  • 未完成:本 SOP 的判档阈值(10⁻² / 10⁻³ / 10⁻⁴ S/m)来自 #16 δ 表的工程估算,未在山体现场做交叉验证;A 档判定的”最低期望 A(dB) ≥ 3 dB”是工程经验值,未在 PSG/EEG 信噪比框架下做完整展开。

七、相关阅读(五池池 ④)

  • mountain-elf-shielding-coefficient.md — 靠山 ELF 屏蔽系数原型文章(#14)
  • building-mountain-terrain-elf-attenuation-analogy.md — 建筑-山体地形衰减类比(#15)
  • skin-depth-basement-building-mu-metal-table.md — δ 表基线(#16)
  • mountain-elf-typical-granite-transparent.md — 普通花岗岩透明负结果(#23)
  • experiments/pool4-mountain-sample-priority-sigma-pre-screening-sop.md — 配套实验设计

引用

  • PMID 20000094 — 建筑地磁屏蔽 1.2–2.0× 衰减;用于交叉佐证山体/建筑 σ 量级差。
  • PMC 12906345 — 干玄武岩 σ ≈ 1–10 S/m @ 1100°C(地幔条件);为 A 档判档阈值提供高温端参照。
  • ResearchGate 238536200 — 干花岗岩 σ 区间 10⁻⁸–10⁻⁴ S/m 与频响依赖;为 C 档判档阈值提供低温端参照。

免责说明:本文属传统知识与科学文献的整理、对照与研究设计讨论,仅供理解与参考,不构成医疗建议,不能替代专业诊断与治疗。文中涉及的效应量、频率区间与暴露结论多为研究报告层面的推断,个体情况差异很大;如有身体不适或健康疑虑,请就医并由专业医师判断。

Rearranging Priority for Mountain Shielding ELF Samples and Sigma Pre-screening SOP

Evidence level: C

Objective: Prior to entering Stage 3 of the multi-profile MT field measurements, use rock body electrical conductivity ($\sigma$) to categorize candidate mountains into three tiers. This prevents running measurements over “ELF transparent terrain.”
Scope: This SOP covers mountain sample screening specifically for “靠山 terrain 1–30 Hz ELF shielding measurements.” It does not extend to electromagnetic radiation biological effects and does not replace the engineering specifications for multi-profile MT station site selection.
Evidence Level: C (Engineering formulas + literature $\sigma$ ranges + structural analogy from Pool #16 $\delta$ table), not entering the biological effects layer.


I. Why Pre-screening is Mandatory

The synthesis of negative results from Round 23 (mountain-elf-typical-granite-transparent.md) yields a single-point estimate of 7.83 Hz:

Mountain Material $\sigma$ (S/m) $\delta$(7.83 Hz) 1 km Mountain $A(dB)$
Ordinary Granite (Dry) $10^{-8}–10^{-4}$ Hundreds of meters – Several km $\approx 0.27$ dB (well below Schumann background fluctuation $\pm1–3$ dB)
Wet Granite (Water-bearing/Mineralized) $10^{-3}–10^{-1}$ Tens of meters – Hundreds of meters 1–10 dB magnitude
Wet Basalt $10^{-2}–10^{0}$ Meters – Tens of meters Tens of dB magnitude

Core Conclusion: Ordinary granite mountains are almost transparent to 7.83 Hz ELF ($A(dB) < 1$ dB); measurements are likely to yield “zero results,” failing to falsify the靠山 ELF shielding hypothesis. Pre-screening via $\sigma$ allows us to concentrate limited human and instrument resources on samples with the highest discriminative power.

Disclaimer: This table derives from Pool #16 $\delta$ table + Round 23 negative result synthesis; it does not rely on new literature for this round.


II. Three-Tier Sample Priority

Candidate靠山 terrains are categorized into three tiers based on $\sigma$ pre-screening (determined by measured $\sigma$ of 10 g rock samples, not relying on geological maps/satellite imagery/folk naming):

Tier Mountain Type $\sigma$ (S/m) 1 km $A(dB)$ @ 7.83 Hz Measurement Value Recommendation
Tier A (Priority) Wet basalt, metal sulfide/mineralized bodies, altered rocks in fault zones $\ge 10^{-2}$ $\ge 10$ dB High (capable of falsifying H1 strong shielding) First batch of measurement points
Tier B (Conditional) Water-bearing/fissured granite, clay fault zones, salt-infiltrated limestone $10^{-3}–10^{-1}$ 1–10 dB Medium (verify H0/H1 boundary) Proceed only if budget remains after Tier A
Tier C (Skip or Control) Dry unaltered granite, outer edge of igneous rocks, dense unfossilized basement $\le 10^{-4}$ $< 1$ dB Negligible (transparent per formula) Skip, unless used as a “zero control” baseline

Core Rationale: Samples with $A(dB) < 1$ dB are completely indistinguishable within the PSG/EEG signal-to-noise ratio (30–50 dB); Tier C measurements yield non-publishable data, wasting instrument time.


III. Specific Procedures for $\sigma$ Pre-screening

3.1 Desktop Pre-screening (No Hiking Required)

  1. Geological Maps + Remote Sensing: Use 1:50,000 or 1:200,000 regional geological maps to identify靠山 terrains; prioritize rock types identified as basalt, diabase, magnetite, mineralized granite, faulted/fractured zones, or areas with hot spring/geothermal outcrops.
  2. MT Public Data Cross-check: Query IRIS/EMAGE, EarthScope, USArray MT stations to check nearby ground resistivity ($\rho = 1/\sigma$) in the 0.001–10 Hz range. If existing 1–10 Hz measured $\rho \le 100$ $\Omega\cdot$m (i.e., $\sigma \ge 10^{-2}$ S/m), directly classify as Tier A.
  3. Hydrogeological Archives: Check local water authority/geothermal/mining rights public data; presence of geothermal wells, hot springs, aquifers, or mineral bodies suggests higher $\sigma$.

3.2 Field Pre-screening (Mandatory Before Hiking)

  1. Prepare 10 g rock powder + distilled water for slurry conductivity: Use a portable EC meter (e.g., HANNA HI98311) to measure slurry conductivity. Values $> 2000$ $\mu$S/cm suggest higher $\sigma$ ($> 10^{-3}$ S/m magnitude), indicating Tier A/B candidates; values $< 200$ $\mu$S/cm likely indicate Tier C.
  2. Handheld Susceptibility Meter (KT-10 / SM-30): Measure magnetic susceptibility. Rock bodies containing magnetite/maghemite with $\chi > 1000 \times 10^{-5}$ SI show strong Tier A signals; $\chi < 50 \times 10^{-5}$ SI typically indicates ordinary granite/sandstone, suggesting Tier C signals.
  3. Simple Four-point Method Small Profile: Use 4 stainless steel electrodes + 1.5 V battery + multimeter for a 0.5 m Wenner array. Calculate $\rho = 2\pi a \cdot V/I$. Compare with known granite $\rho$ magnitude ($10^{3}–10^{5}$ $\Omega\cdot$m); if lower by $\ge 1$ order of magnitude, upgrade one tier.

3.3 Tolerance Handling for $\sigma$ Uncertainty

Rock electrical conductivity is affected by temperature, water content, porosity, and frequency bands, with a variance of at least $\pm 1$ order of magnitude (literature interval values reflect this). When assigning tiers, adopt the “Lower Limit Principle”:

  • If desktop pre-screening yields a Tier A lower limit (e.g., $\sigma \ge 10^{-2}$ S/m), proceed with Tier A protocols;
  • Samples at tier boundaries ($10^{-4}–10^{-3}$ S/m) should be upgraded to the higher tier for priority measurement to avoid missing data;
  • The “minimum expected $A(dB)$” for any tiered classification should be $> 3$ dB; otherwise, downgrade the tier.

IV. Integration with Existing Projects

Existing Project Integration Method
#14 靠山 ELF Shielding Coefficient Measurement Before Stage 3 multi-profile MT site selection, execute this SOP first to output a “Three-Tier Candidate Mountain List” as input for site selection
#15 Building-Mountain Terrain Attenuation Analogy Stage 2-3 need not extend to ordinary granite (Tier C); only connect $\sigma$ data from Tier A/B for analogy verification
#16 $\delta$ Table $\sigma/\mu_r$ Intervals The tier thresholds in this SOP specifically realize the Tier A ($10^{-2}$), Tier B ($10^{-3}$), and Tier C ($10^{-4}$) from Pool #16 table
#17 Schumann Mountain FEM Change FEM candidate points to wet basalt (Tier A); skip ordinary granite FEM
#18 Schumann Mountain vs. Plain Literature Baseline 🛑 Temporarily suspended; upon release, the station name anchors in this SOP (USArray MT, EarthScope, IRIS stations) can serve as indirect anchors for literature backfilling

V. Falsification and Downgrade Contingency Plans

Failure Scenario Criterion Action
Tier A mountain $\sigma$ measured $< 10^{-3}$ S/m Desktop/Field pre-screening error Switch to Tier B point or re-measure
Tier A mountain measured $A(dB) < 3$ dB Hypothesis H1 strong shielding not established Write “negative result + white paper,” merge into Long Meridian Protocol Appendix
Tier A mountain measured $A(dB) \ge 5$ dB H1 strong shielding confirmed Lock #14 H1a; proceed to #15 analogy verification
No significant $\sigma$ difference across A/B/C tiers Pre-screening invalid Upgrade to “exhaustive control” mode, measure all tiers

VI. Evidence and Limitations

  • Supporting Literature: Dry granite $\sigma$ range $10^{-8}–10^{-4}$ S/m with frequency dependence (ResearchGate 238536200); dry basalt melt $\sigma \approx 1–10$ S/m (PMC 12906345). The 4–5 order of magnitude gap in $\sigma$ provided by merging these two literatures forms the factual basis for this SOP’s tiering.
  • Not Addressed: Biological effects, Schumann node shifts, human PSG/EEG responses; these are handled separately by #17, #18, and Pool ③.
  • Incomplete: The tier thresholds ($10^{-2} / 10^{-3} / 10^{-4}$ S/m) in this SOP come from engineering estimates in Pool #16 $\delta$ table without cross-validation at the mountain site; the “minimum expected $A(dB) \ge 3$ dB” for Tier A is an engineering experience value not fully expanded within the PSG/EEG signal-to-noise ratio framework.

VII. Related Reading (Pool ④)

  • mountain-elf-shielding-coefficient.md — Prototype article for靠山 ELF shielding coefficient (#14)
  • building-mountain-terrain-elf-attenuation-analogy.md — Building-mountain terrain attenuation analogy (#15)
  • skin-depth-basement-building-mu-metal-table.md — $\delta$ table baseline (#16)
  • mountain-elf-typical-granite-transparent.md — Ordinary granite transparent negative result (#23)
  • experiments/pool4-mountain-sample-priority-sigma-pre-screening-sop.md — Supporting experimental design

References

  • PMID 20000094 — Building geomagnetic shielding 1.2–2.0$\times$ attenuation; used for cross-validation of mountain/building $\sigma$ magnitude differences.
  • PMC 12906345 — Dry basalt $\sigma \approx 1–10$ S/m @ 1100°C (mantle conditions); provides high-temperature reference for Tier A threshold.
  • ResearchGate 238536200 — Dry granite $\sigma$ range $10^{-8}–10^{-4}$ S/m with frequency dependence; provides low-temperature reference for Tier C threshold.

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *