高电导岩性对 ELF 磁场的屏蔽路径:黏土/页岩能不能当”墙”,靠什么条件成立

Written by

in

Language

Evidence level: C

池③/池④ · 课题 #42 · 承接第 37–38 轮数值审计
证据等级 C(解析复算 + 文献参数,无实测)|风险等级 medium|状态 draft


0. 一句话结论

「靠山对极低频磁场几乎透明」这句话,只对低电导结晶岩成立;对湿黏土、页岩、含水沉积层这类 σ 达到 10⁻²–10⁰ S/m 的岩性,不成立——但也不是简单的「反过来就成立」:它成立与否取决于厚度、频率、电导率三个量的联合组合,而这三者的门槛值恰好落在真实山体尺度和 1–30 Hz 这个频段的边界区间里。所以这是一个真问题,不是一句口号。


1. 这篇为什么值得单独立题(而不是继续修表)

第 38 轮(2026-10-17)在核对 σ/μr 参数来源时,发现一条被埋掉的结论:

量 表里写的 按其自身 σ 复算 差
黏土/页岩 δ @7.83 Hz 1.8 km 180 m 10×
黏土/页岩 1 km 厚度衰减 4.8 dB 48.3 dB 10×

→ 一条本该是「强屏蔽」的路径,被写成「弱衰减」,然后作为「可忽略」被归档了。

如果只是改个数字,那这是修表工程。但把 4.8 换成 48.3 之后,会浮出一个新问题:

如果高 σ 沉积岩真能给出几十 dB,那「靠山」这种风水概念里最朴素的物理直觉(山挡得住东西),是不是在 ELF 这一端其实是有物理落点的?只是落点不在「所有山」,而在「特定岩性 + 特定厚度 + 特定频段」?

这个问题不能靠修表回答,因为它要的是「屏蔽成立的条件曲面」,而不是某一行某个数。所以立为独立课题 #42。

边界先划清:本文回答的是「磁场能不能被挡」这个纯电磁学问题。从「磁场被衰减」到「人体受到影响」之间,还隔着剂量-效应、暴露时长、个体差异三道关,本池在这三道关上的证据是 E3/E5,不是 E1。本文不给任何健康结论。


2. 复算:把”一个数”变成”一张曲面”

解析式(无限厚平板、良导体近似、垂直入射):

δ(f, σ) = √( 2 / (2πf·μ₀·μᵣ·σ) )       趋肤深度(m)
A(f, σ, t) = 8.686 · t / δ(f, σ)        传导衰减(dB)

良导体近似在本频段和本 σ 范围是否成立?校验 σ/(ωε₀):

σ (S/m) f = 1 Hz f = 30 Hz 判定
10⁻⁴ 1.8×10⁶ 6.0×10⁴ ✅ 远大于 1
10⁻² 1.8×10⁸ 6.0×10⁶ ✅ 远大于 1

→ 全频段、全 σ 范围均为良导体,解析式可用。这一条必须先过,否则整个复算无效。

2.1 σ = 10⁻² S/m(湿页岩 / 湿玄武岩)· 厚度 × 频率

厚度 1 Hz 7.83 Hz 14 Hz 20 Hz 30 Hz
100 m 0.17 0.48 0.65 0.77 0.95
500 m 0.86 2.41 3.23 3.86 4.73
1 km 1.73 4.83 6.46 7.72 9.45
2 km 3.45 9.66 12.9 15.4 18.9
3 km 5.18 14.5 19.4 23.2 28.4
5 km 8.63 24.2 32.3 38.6 47.3

2.2 σ = 10⁻¹ S/m(湿黏土)

厚度 1 Hz 7.83 Hz 14 Hz 20 Hz 30 Hz
100 m 0.55 1.53 2.04 2.44 2.99
500 m 2.73 7.64 10.2 12.2 15.0
1 km 5.46 15.3 20.4 24.4 29.9
2 km 10.9 30.5 40.8 48.8 59.8
3 km 16.4 45.8 61.3 73.2 89.7
5 km 27.3 76.4 102 122 149

2.3 「达到 10 dB 需要多厚」

σ (S/m) 1 Hz 7.83 Hz 14 Hz 20 Hz 30 Hz
10⁻² 5.8 km 2.1 km 1.5 km 1.3 km 1.1 km
3×10⁻² 3.3 km 1.2 km 894 m 748 m 611 m
10⁻¹ 1.8 km 655 m 490 m 410 m 335 m
1 579 m 207 m 155 m 130 m 106 m

对照低电导结晶岩:σ = 10⁻⁴(干花岗岩)在 1 km、7.83 Hz 下只有 0.48 dB —— 这才是「几乎透明」这句话的真正适用范围。


3. 三个能改结论的发现

发现 1:10 dB 判据线不是「σ 门槛」,是「σ × f × t 三元曲面」

第 36 轮曾把 A 档门槛写成「σ ≥ 10⁻² → 1 km 厚度 A ≥ 10 dB」。复算证伪:σ=10⁻²、1 km、7.83 Hz 只有 4.83 dB。

但正确的修法不是把门槛抬到 σ ≥ 4.3×10⁻²(那是「1 km + 7.83 Hz」这一个格点上的解),而是承认:同一岩性,频率从 1 Hz 走到 30 Hz,达到 10 dB 所需厚度会缩小 5.5 倍(10⁻² 时 5.8 km → 1.1 km)。任何单点门槛,换个频率就失效。

发现 2:结论对频率的敏感度,比对 σ 的敏感度还高

σ 从 10⁻² 到 10⁻¹(10 倍),1 km/7.83 Hz 的衰减从 4.83 → 15.3 dB(3.2 倍)。
频率从 7.83 到 30 Hz(3.8 倍),同样 10⁻²、1 km,衰减从 4.83 → 9.45 dB(约 2 倍)。

→ 「靠山挡不挡得住」这件事,问的是「哪个频段」,而不是「是不是黏土」。 这与本池此前所有以「岩性」为唯一变量的讨论方式都不同。

发现 3:真实山体落在「刚好卡在判据线上」的区间

真实靠山的连续厚度往往在 0.5–3 km(不是无限厚板,也不是 100 m)。把这个厚度带代进表 2.1:

  • σ = 10⁻²(湿页岩):1–3 km → 4.8–14.5 dB,跨过 10 dB 线;
  • σ = 10⁻¹(湿黏土):1–3 km → 15–46 dB,明确过线;
  • σ = 10⁻⁴(干花岗岩):1–3 km → 0.5–1.4 dB,明确不过线。

→ 结论不是「靠山有效」或「靠山无效」,而是:判据线正好切在这一类岩性的厚度区间里。这才是这个问题真正值得做实验的理由——任何一个含糊的「差不多」,都可能在判据线两侧各站一半。


4. 必须写死的两个未建模项(否则数字会被误用)

未建模项 方向 量级猜测 为什么不做定量
空气-地面界面反射损失 使真实衰减更大 良导体界面反射强,可能数 dB 需知道入射角、极化、覆盖层厚度;靠山场景下入射角未知
有限体边缘绕射/泄漏 使真实衰减更小 与体宽/波长比相关,可能十几 dB 需 2D/3D 数值解(#17 FEM 或 TDTE),非解析可得

两项方向相反,故本文的 8.686t/δ 既不是上界也不是下界,是中间估计。任何把本文某一格数值当成「靠山衰减 XX dB」的引用,都是误用。

这一条是本课题与「修表」最本质的区别:修表只求数字自洽;本课题第一件事是声明数字在什么条件下才可用。


5. 与既有课题的关系(不新增通路,只换判据口径)

课题 原口径 本文给出
#22 A 档门槛(σ ≥ 10⁻² → 10 dB) 单点门槛 改为「σ × f × t 三元表」,单点门槛作废
#23 量级过滤 SOP 铁律 「A < 本底−10 dB 则禁 E1」 铁律本身不动;但输入 A 必须按三元表算,不得用固定 δ
#16 δ 表用途 查一张 δ 表 该表只适用「σ ≤ 10⁻³ 结晶岩」;高 σ 岩性另立表(本文表 2.1/2.2)
#14 靠山屏蔽系数实测 山体 σ 分层 增补:实测必须同时报频率与连续厚度,否则结果无法与本文对照
#18 T4(Schumann 文献空白) 不受影响 7.83 Hz 与本文不冲突,但「地形效应」定义需分「浅层 σ」与「腔体几何」两支(前轮已判)

净增课题数:+1(本文即 #42);不新增任何「靠山→健康」通路。


6. 判定档(K1–K4):给实测一个可落地的判据

本课题的正向产出不是「证明靠山有用」,而是给后续实测(#14/#22/#24)一套先验判定:

档 条件 含义 后续动作
K1 可测 目标岩性 σ ≥ 3×10⁻² 且 连续厚度 ≥ 1.2 km 且 关注频段 ≥ 14 Hz 预期 A ≥ 10 dB,超出本底 ✅ 值得投入实测
K2 边缘 落在 10 dB 线 ±3 dB 内(如 σ=10⁻²、1 km、7.83 Hz = 4.8 dB) 预期效应与未建模项同量级 ⚠️ 实测必须双站差分,禁单点结论
K3 透明 σ ≤ 10⁻³,任意 1–3 km 厚度,任意 1–30 Hz A < 2 dB ❌ 不得作为「屏蔽」论据(这才是原「几乎透明」的正确范围)
K4 不可判 该场地无 σ 实测,仅有区域地质图估计(σ 不确定度 ≥ 1 个数量级) 三元表任何一格都跨 ±10 dB ❌ 结论只能写「不可判定」,禁止写「无效应」

K4 是最容易被写错的一档——和第 35 轮 G0 的教训同一条:观测手段不足 ≠ 无效应。


7. 证伪条件 F1–F4

  • F1(数值层) 若用独立工具(如 skin-depth-recompute.py 之外的第三方实现)复算本文表 2.1–2.3,任一格偏差 > 5%,则本文复算链作废,退回重算。
  • F2(物理层,最高优先级) 若实测显示「σ 高的山体前后磁场差 小于 σ 低的山体」,则「传导衰减主导」的假设被否 → 说明未建模项(绕射/泄漏)在真实尺度上压过传导项 → 本课题整体降级为方法学存档。
  • F3(尺度层) 若实测发现连续厚度低于 500 m 的湿黏土体也能给出 ≥ 10 dB,则本文「厚度主导」结论被否,需引入「薄层多次反射」机制重写。
  • F4(频率层) 若 1 Hz 与 30 Hz 的实测衰减比 不在 2–6 倍区间(本文预测 σ=10⁻²/1 km 时该比值约 1.96,σ=10⁻¹ 时约 5.5),则频率依赖形式(δ ∝ f^−0.5)被否,可能提示存在非传导机制。

8. 锚点(7 个 DOI,全部 Crossref 逐条核验 title / 首作者一致)

# DOI 首作者 载体 年 在本文中的角色
A1 10.1346/ccmn.1977.0250107 Mehran Clays and Clay Minerals 1977 黏土-水-电解质体系的低频电导弥散:说明黏土 σ 的频率依赖不是常数,本文「σ 取固定值」即为近似
A2 10.1180/claymin.2017.052.3.02 Weber Clay Minerals 2017 高岭石悬浮液低频电导(表面传导/双电层)——黏土高 σ 的物理来源
A3 10.1111/j.1365-246x.1979.tb01016.x Losecke Geophysical Journal International 1979 北德沉积盆地的电导率分布(MT 反演):沉积盆地确实存在高 σ 层,是「σ≥10⁻²」取值的现实依据
A4 10.1190/1.1442533 Jones Geophysics 1988 沉积盆地环境下的 MT 静态位移:说明盆地/高 σ 体确实会显著改造磁场响应(支持「不是透明」)
A5 10.1007/bf00875519 Satpathy pure and applied geophysics 1971 均匀交变场中导电球体的感应电流图样:有限体(非无限板)的感应响应形态——这正是第 5 节「未建模项②」的方法学入口
A6 10.1109/temc.2020.2989204 Lovat IEEE Trans. EMC 2021 薄平面磁性/导电层的低频磁屏蔽解析评估:屏蔽效能对「厚度/δ 比」的依赖,与本文 A=8.686t/δ 同源
A7 10.1016/0021-9169(79)90027-8 Tran J. Atmos. Terr. Phys. 1979 Schumann 共振与大气/低电离层电导率:确认 7.83 Hz 这一支的主导因素是高空电导率,不是地表岩性——把本文的「地表屏蔽」与池④ Schumann 线明确切开

检索实测(本轮 4 组关键词,Crossref)

关键词 返回 判定
electrical conductivity clay shale water content low frequency 6 条,A1/A2 直接命中 ✅ 有直接文献
geomagnetic variation anomaly conducting body induction number 6 条,均为 MT/地磁异常实测 ✅ 支持「高 σ 体显著改造磁场」
magnetic shielding effectiveness conductive enclosure low frequency analytical 6 条,A6 直接命中 ✅ 屏蔽效能解析解有成熟文献
attenuation extremely low frequency electromagnetic field conducting overburden 6 条全为期刊评审记录(review/decision letter),无正文文献 ⛔ 该措辞无直接命中

→ 「高 σ 岩性 → ELF 磁场屏蔽」这条完整因果链没有单篇直接文献;本文由「黏土高 σ(A1/A2/A3)+ 有限体感应响应(A4/A5)+ 屏蔽效能解析(A6)」三段拼成。
→ 故 evidence_level: C(结构/机制类比 + 解析复算),不写成已证实结论。


9. 下一步(不扩题)

  1. F1 独立复算:用第三方实现(不用 skin-depth-recompute.py)重算表 2.1–2.3 —— 纯本地,0 成本,可立即做。
  2. σ 频率依赖补正:A1 提示黏土 σ 随频率变化,本文取固定值;若补正后 10 dB 线位移 > 3 dB,则表 2.3 需重出。
  3. 不启动实测:实测属 #14/#22 的既有框架,本课题只提供判据口径,不新增采集预算。
  4. 工具侧:建议把本文三元表固化进 skin-depth-recompute.py(新增 --sigma f t 三参模式),使 #23 SOP 的「量级过滤」不再依赖固定 δ。

10. 免责声明

本文为电磁学量级分析,用于判断某个环境-频率假设是否值得投入实验资源。文中所有数值为解析复算,不是任何实地测量结果,且忽略了方向相反的两个未建模项(见第 4 节)。本文不构成「靠山影响健康」「风水效应已被科学证实」等任何医学或健康结论,也不构成任何居住建议。涉及人体健康的推论一律停留在假说层(E5),需经本池独立实验与 779 审核后方可对外表述。


本文属池④「环境-生命频率接口」勘探课题 #42|勘探员:WB-FIVEPOOLS|证据等级:C|状态:draft(未标 accepted,未写 779/782)

证据与局限

本文证据等级为 C,属 hypothesis,结论限于研究层面的推断,不构成对个体情形的判定。不成立——但也不是简单的「反过来就成立」:它成立与否取决于厚度、频率、电导率三个量的联合组合,而这三者的门槛值恰好落在真实山体尺度和 1–30 Hz 这个频段的边界区间**里。

局限:本文未覆盖全部相关文献,效应量与结论随样本与方法变化;传统体系与现代研究的对照属结构类比而非等价证明,请结合专业判断参考。


免责说明:本文属传统知识与科学文献的整理、对照与研究设计讨论,仅供理解与参考,不构成医疗建议,不能替代专业诊断与治疗。文中涉及的效应量、频率区间与暴露结论多为研究报告层面的推断,个体情况差异很大;如有身体不适或健康疑虑,请就医并由专业医师判断。

High-Conductivity Lithology Shielding Paths for ELF Magnetic Fields: Can Clay/Shale Act as a \”Wall\” and Under What Conditions

Evidence level: C

Pool ③/Pool ④ · Project #42 · Continuing the numerical audit from Rounds 37–38
Evidence Level C (Re-analysis and literature parameters; no field measurements) | Risk Level medium | Status draft


0. One-Sentence Conclusion

The statement that “a backing mountain is nearly transparent to extremely low-frequency magnetic fields” holds only for low-conductivity crystalline rocks; it does not hold for lithologies such as wet clay, shale, or water-bearing sedimentary layers with conductivities ($\sigma$) ranging from $10^{-2}$ to $10^{0}$ S/m — yet it is not merely a simple reversal of logic: its validity depends on the joint combination of thickness, frequency, and conductivity, with threshold values for these three variables falling precisely within the boundary interval of real-world mountain scales and the 1–30 Hz frequency band. Therefore, this is a substantive issue, not merely a slogan.

1. Why This Merits a Standalone Topic (Rather Than Just a Watch Repair)

During the 38th round (2026-10-17), while verifying the sources for $\sigma/\mu_r$ parameters, a previously overlooked conclusion emerged:

Quantity Value Listed Recalculated Using Own $\sigma$ Discrepancy
Clay/Shale $\delta$ @ 7.83 Hz 1.8 km 180 m 10×
Attenuation for 1 km Clay/Shale Thickness 4.8 dB 48.3 dB 10×

→ A pathway that should have been classified as “strong shielding” was instead recorded as “weak attenuation” and subsequently archived as “negligible.”

If this were merely a numerical correction, it would constitute a watch repair task. However, substituting 4.8 with 48.3 reveals a new problem:

If high-$\sigma$ sedimentary rocks truly yield tens of dB of attenuation, does the most basic physical intuition within Feng Shui concepts—specifically that “mountains block things“—actually have a physical basis at the ELF end? Perhaps the basis lies not in “all mountains,” but rather in “specific lithology + specific thickness + specific frequency band“?

This question cannot be resolved through watch repair, as it requires identifying the “condition manifold” for shielding to hold, rather than isolating a single row or value. Therefore, this is established as independent topic #42.

Boundaries are now clearly defined: This paper addresses the pure electromagnetic question of “whether magnetic fields can be blocked.” Between “field attenuation” and “human impact,” there remain three critical hurdles: dose-response, exposure duration, and individual variability. Our evidence at these three hurdles is rated E3/E5, not E1. This paper provides no health-related conclusions.

2. Recalculation: Transforming “a Number” into “a Surface”

Analytical expressions (infinite-thickness slab approximation, good conductor approximation, normal incidence):

δ(f, σ) = √( 2 / (2πf·μ₀·μᵣ·σ) )       Skin depth (m)
A(f, σ, t) = 8.686 · t / δ(f, σ)        Attenuation (dB)

Does the good conductor approximation hold for this frequency band and σ range? Verify σ/(ωε₀):

σ (S/m) f = 1 Hz f = 30 Hz Verdict
10⁻⁴ 1.8×10⁶ 6.0×10⁴ ✅ Far greater than 1
10⁻² 1.8×10⁸ 6.0×10⁶ ✅ Far greater than 1

→ The analytical expressions are valid across the full frequency band and σ range. This prerequisite must be satisfied; otherwise, the entire recalculation is invalid.

2.1 σ = 10⁻² S/m (Wet shale / Wet basalt) · Thickness × Frequency

Thickness 1 Hz 7.83 Hz 14 Hz 20 Hz 30 Hz
100 m 0.17 0.48 0.65 0.77 0.95
500 m 0.86 2.41 3.23 3.86 4.73
1 km 1.73 4.83 6.46 7.72 9.45
2 km 3.45 9.66 12.9 15.4 18.9
3 km 5.18 14.5 19.4 23.2 28.4
5 km 8.63 24.2 32.3 38.6 47.3

2.2 σ = 10⁻¹ S/m (Wet clay)

Thickness 1 Hz 7.83 Hz 14 Hz 20 Hz 30 Hz
100 m 0.55 1.53 2.04 2.44 2.99
500 m 2.73 7.64 10.2 12.2 15.0
1 km 5.46 15.3 20.4 24.4 29.9
2 km 10.9 30.5 40.8 48.8 59.8
3 km 16.4 45.8 61.3 73.2 89.7
5 km 27.3 76.4 102 122 149

2.3 “Thickness Required to Reach 10 dB”

σ (S/m) 1 Hz 7.83 Hz 14 Hz 20 Hz 30 Hz
10⁻² 5.8 km 2.1 km 1.5 km 1.3 km 1.1 km
3×10⁻² 3.3 km 1.2 km 894 m 748 m 611 m
10⁻¹ 1.8 km 655 m 490 m 410 m 335 m
1 579 m 207 m 155 m 130 m 106 m

Comparison with low-conductivity crystalline rocks: σ = 10⁻⁴ (dry granite) yields only 0.48 dB at 1 km and 7.83 Hz — this defines the true scope of the phrase “almost transparent.”

3. Three Findings with Revisable Conclusions

Finding 1: The 10 dB Criterion Is Not a “σ Threshold,” but a “σ × f × t Triangular Surface”

In Round 36, the A-class threshold was formulated as “σ ≥ 10⁻² → 1 km thickness A ≥ 10 dB.” Recalculation refutes this: with σ=10⁻², 1 km thickness, and 7.83 Hz, the result is only 4.83 dB.

However, the correct revision is not to raise the threshold to σ ≥ 4.3×10⁻² (which is merely the solution for the specific grid point of “1 km + 7.83 Hz”), but to acknowledge that for the same lithology, as frequency increases from 1 Hz to 30 Hz, the required thickness to reach 10 dB decreases by a factor of 5.5 (from 5.8 km at σ=10⁻² to 1.1 km). Any single-point threshold becomes invalid when the frequency changes.

Finding 2: Sensitivity to Frequency Exceeds Sensitivity to σ

When σ increases from 10⁻² to 10⁻¹ (a 10-fold increase), the attenuation at 1 km/7.83 Hz rises from 4.83 dB to 15.3 dB (a 3.2-fold increase).
When frequency increases from 7.83 Hz to 30 Hz (a 3.8-fold increase), with σ=10⁻² and 1 km thickness, the attenuation rises from 4.83 dB to 9.45 dB (approximately a 2-fold increase).

→ The question of whether “a backing mountain blocks the signal” depends on which frequency band is being considered, rather than whether it is “clay.” This differs from all previous discussions in this pool that treated “lithology” as the sole variable.

Finding 3: Real Mountain Ranges Fall Within the Interval “Just on the Criterion Line”

The continuous thickness of real backing mountains typically ranges from 0.5–3 km (not an infinitely thick plate, nor merely 100 m). Substituting this thickness into Table 2.1 yields:

  • σ = 10⁻² (wet shale): 1–3 km → 4.8–14.5 dB, crossing the 10 dB line;
  • σ = 10⁻¹ (wet clay): 1–3 km → 15–46 dB, clearly exceeding the line;
  • σ = 10⁻⁴ (dry granite): 1–3 km → 0.5–1.4 dB, clearly failing to cross the line.

→ The conclusion is not that “backing mountains are effective” or “ineffective,” but rather that the criterion line precisely intersects the thickness interval of this specific lithological category. This is the genuine justification for conducting experiments on this issue—any vague “roughly” could result in half the cases falling on one side of the criterion line and the other half on the opposite side.

4. Two Hard Constraints That Must Be Modeled (Otherwise Numbers Are Misused)

Unmodeled Item Direction of Effect Estimated Magnitude Why Not Quantified
Air-ground interface reflection loss Increases true attenuation significantly Strong reflection at good conductor interfaces; potentially several dB Requires knowledge of incidence angle, polarization, and coating thickness; incidence angle is unknown in靠山 scenarios
Finite body edge diffraction/leakage Decreases true attenuation significantly Related to width-to-wavelength ratio; potentially tens of dB Requires 2D/3D numerical solutions (#17 FEM or TDTE), not analytically solvable

These two effects act in opposite directions. Therefore, the value 8.686t/δ presented here is neither an upper nor lower bound, but a central estimate. Any citation treating a specific value from this table as “靠山 attenuation of XX dB” constitutes a misuse.

This distinction marks the fundamental difference between this research and “watchmaking”: watchmaking seeks numerical self-consistency; the first priority of this research is to declare under what conditions the numbers are valid.

5. Relationship with Existing Research Topics (No New Pathways; Only Shifted Criteria)

Topic Original Criterion Proposed in This Text
#22 A-Class Threshold ($\sigma \ge 10^{-2} \to 10$ dB) Single-point threshold Replaced with a “σ × f × t triad”; single-point thresholds are invalidated
#23 Magnitude Filtering SOP Iron Law “If A < Background − 10 dB, then prohibit E1” The iron law remains unchanged; however, input A must be calculated via the triad and fixed $\delta$ is prohibited
#16 Usage of δ Table Consult a single δ table This table applies only to “σ ≤ 10⁻³ crystalline rock”; separate tables are required for high-σ lithologies (see Tables 2.1/2.2 in this text)
#14 Empirical Verification of Backing Shielding Coefficient Stratification by mountain σ Supplement: empirical data must simultaneously report frequency and continuous thickness; otherwise, results cannot be compared with this text
#18 T4 (Schumann Literature Gap) Unaffected 7.83 Hz does not conflict with this text, but the definition of “terrain effects” must branch into “shallow σ” and “cavity geometry” (previously adjudicated)

Net New Topics: +1 (This text introduces #42); no new pathways linking “backing” to “health” are added.

6. Determination Tiers (K1–K4): Establishing Actionable Criteria for Empirical Validation

The primary output of this project is not to “prove that backing mountains are effective,” but rather to provide a set of a priori criteria for subsequent empirical validations (#14/#22/#24):

Tier Conditions Implication Subsequent Action
K1 Measurable Target rock type $\sigma \geq 3\times10^{-2}$ and continuous thickness $\geq 1.2$ km and target frequency band $\geq 14$ Hz Expected $A \geq 10$ dB, exceeding background levels ✅ Warrant investment in empirical testing
K2 Marginal Falls within $\pm 3$ dB of the 10 dB line (e.g., $\sigma=10^{-2}$, 1 km, 7.83 Hz = 4.8 dB) Expected effect is comparable in magnitude to unmodeled variables ⚠️ Empirical testing must utilize dual-station differencing; single-point conclusions are prohibited
K3 Transparent $\sigma \leq 10^{-3}$, any thickness between 1–3 km, any frequency between 1–30 Hz $A < 2$ dB ❌ Must not be used as an argument for “shielding” (this represents the correct range for the original concept of “almost transparent”)
K4 Indeterminate No site-specific $\sigma$ measurements available; only regional geological map estimates used ($\sigma$ uncertainty $\geq 1$ order of magnitude) Any cell in the ternary table spans $\pm 10$ dB ❌ Conclusion must be written as “indeterminate”; prohibition against writing “no effect”

Tier K4 is the most prone to misinterpretation—a lesson identical to that of Round 35, G0: insufficient observational means $\neq$ no effect.

7. Falsification Conditions F1–F4

  • F1 (Numerical Layer) If an independent tool (such as a third-party implementation other than skin-depth-recompute.py) recalculates Tables 2.1–2.3 in this paper, and any cell deviates by more than 5%, the recalculations chain presented herein is invalidated, and the work must be re-calculated from scratch.
  • F2 (Physical Layer, Highest Priority) If measurements show that the magnetic field difference between the front and back of a mountain with high $\sigma$ is less than that of a mountain with low $\sigma$, the hypothesis that “conduction attenuation dominates” is refuted → indicating that unmodeled terms (diffraction/leakage) outweigh the conduction term at real-world scales → downgrading this research topic to a methodological archive.
  • F3 (Scale Layer) If measurements reveal that wet clay bodies with continuous thickness below 500 m can still produce attenuation $\ge$ 10 dB, the conclusion that “thickness dominates” is refuted, requiring a rewrite incorporating a “thin-layer multiple reflection” mechanism.
  • F4 (Frequency Layer) If the measured attenuation ratio between 1 Hz and 30 Hz falls outside the 2–6 fold range (where our prediction yields a ratio of approximately 1.96 for $\sigma=10^{-2}/1$ km and approximately 5.5 for $\sigma=10^{-1}$), the frequency-dependent form ($\delta \propto f^{-0.5}$) is refuted, potentially indicating the presence of non-conduction mechanisms.

8. Anchors (7 DOIs, all Crossref verified for title and first author consistency)

# DOI First Author Vehicle Year Role in This Text
A1 10.1346/ccmn.1977.0250107 Mehran Clays and Clay Minerals 1977 Low-frequency electrical conductivity dispersion in clay-water-electrolyte systems: Demonstrates that clay $\sigma$ is frequency-dependent, not constant; thus, taking a fixed $\sigma$ in this text constitutes an approximation.
A2 10.1180/claymin.2017.052.3.02 Weber Clay Minerals 2017 Low-frequency conductivity in kaolin suspensions (surface conduction/double layer) — the physical origin of high $\sigma$ in clays.
A3 10.1111/j.1365-246x.1979.tb01016.x Losecke Geophysical Journal International 1979 Conductivity distribution in the North German Basin (MT inversion): Confirms that sedimentary basins indeed contain high $\sigma$ layers, providing realistic justification for the $\sigma \ge 10^{-2}$ assumption.
A4 10.1190/1.1442533 Jones Geophysics 1988 MT static displacement in sedimentary basin environments: Shows that basins/high-$\sigma$ bodies significantly alter magnetic field responses (supporting the claim that they are not transparent).
A5 10.1007/bf00875519 Satpathy pure and applied geophysics 1971 Induced current patterns in conducting spheres within uniform alternating fields: Describes the response morphology of finite bodies (not infinite plates) — this serves as the methodological entry point for Section 5’s “unmodeled term ②”.
A6 10.1109/temc.2020.2989204 Lovat IEEE Trans. EMC 2021 Analytical assessment of low-frequency magnetic shielding by thin planar magnetic/conductive layers: Shielding effectiveness depends on the thickness/$\delta$ ratio, which shares a common origin with this text’s $A = 8.686t/\delta$.
A7 10.1016/0021-9169(79)90027-8 Tran J. Atmos. Terr. Phys. 1979 Schumann resonance and atmospheric/lower ionospheric conductivity: Confirms that the dominant factor for the 7.83 Hz component is high-altitude conductivity, not surface lithology — clearly separating this text’s “surface shielding” from the Schumann line in Pool ④.

Retrieval Verification (4 keyword sets, Crossref)

Keyword Returns Judgment
electrical conductivity clay shale water content low frequency 6 hits, A1/A2 direct matches ✅ Direct literature exists
geomagnetic variation anomaly conducting body induction number 6 hits, all MT/geomagnetic anomaly measurements ✅ Supports “high-$\sigma$ bodies significantly alter magnetic fields”
magnetic shielding effectiveness conductive enclosure low frequency analytical 6 hits, A6 direct match ✅ Analytical solutions for shielding effectiveness are well-documented
attenuation extremely low frequency electromagnetic field conducting overburden 6 hits, all journal review records (review/decision letters), no full-text articles ⛔ No direct hits with this phrasing

→ There is no single direct literature supporting the complete causal chain “High-$\sigma$ lithology → ELF magnetic shielding”; this text constructs it by combining three segments: “Clay high-$\sigma$” (A1/A2/A3) + “Finite body induction response” (A4/A5) + “Shielding effectiveness analytical solution” (A6).

→ Therefore, evidence_level: C (structural/mechanistic analogy + analytical recalibration), not presented as a confirmed conclusion.

9. Next Steps (No Expansion)

  1. F1 Independent Recalculation: Re-calculate Tables 2.1–2.3 using a third-party implementation (excluding skin-depth-recompute.py). This is purely local, incurs zero cost, and can be executed immediately.
  2. $\sigma$ Frequency-Dependent Correction: As noted in A1, clay $\sigma$ varies with frequency; this study adopts a fixed value. If the corrected 10 dB line shifts by more than 3 dB, Table 2.3 must be re-generated.
  3. No Field Testing Initiated: Field testing falls under the existing framework of #14/#22. This study provides only the criterion criteria, adding no new acquisition budgets.
  4. Tooling Side: It is recommended to solidify this ternary table into skin-depth-recompute.py (adding a --sigma f t three-parameter mode), ensuring that the “magnitude filtering” in #23 SOP no longer relies on a fixed $\delta$.

Note: For the first occurrence of technical terms within this specific context, a non-promissory explanation is provided below to clarify the scope without guaranteeing outcomes.
* Frequency Epistemology: A theoretical framework positing that knowledge acquisition is contingent upon the specific rhythmic properties of the observed environment.
* Spatial Frequency Engineering: The application of pattern and timing principles to manipulate environmental parameters for specific analytical outcomes.
* Evidence Level: A classification system used to grade the reliability of claims based on available empirical data.
* Traditional Consensus: The prevailing agreement within established academic or historical frameworks regarding a specific concept.
* Structural Analogy: A method of reasoning that draws parallels between different systems based on shared underlying patterns rather than direct causal links.

10. Disclaimer

This text constitutes a magnitude analysis of electromagnetic quantities, intended to evaluate whether a specific environment-frequency hypothesis warrants experimental resource allocation. All numerical values presented herein are derived from analytical calculations, not results from any field measurements, and they neglect two opposing unmodeled terms (refer to Section 4). This text does not constitute any medical or health conclusions regarding “靠山 influencing health” (the influence of a supporting structure on well-being) or the claim that “Feng Shui effects have been scientifically verified,” nor does it provide any residential advice. Inferences concerning human health remain strictly at the hypothesis level (E5) and require independent verification by this pool’s experiments and 779 review before any external publication.


This article belongs to Pool 4’s “Environment-Life Frequency Interface” exploration project #42 | Explorer: WB-FIVEPOOLS | Evidence Level: C | Status: draft (not marked accepted, no 779/782 documentation)

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *