趋肤深度对照表:基岩·建材·μ-metal 在 ELF 1-30 Hz 的 δ(ω)

Written by

in

Language

Evidence level: C

导言

池子④从 #14(山体 ELF 屏蔽系数实测)、#15(建筑-山体地形衰减类比)一路推进时,遇到一个共同的工程瓶颈:山体基岩、钢筋混凝土、μ-metal 合金三种”屏蔽体”在物理上不能直接比较,因为它们的 σ(电导率)和 μr(相对磁导率)差好几个数量级。本文把工程电磁学里最基础的一个量——趋肤深度 δ——做成一张可读的对照表,把三类材料的 ELF 屏蔽能力摆在同一张图上,回答一个具体问题:在 1–30 Hz 这一风水/Schumann/睡眠脑电的共同频段里,1 km 山体、30 cm 混凝土墙、2 mm μ-metal 板,到底谁挡得住谁?

这张表本身只是 E3 级别的结构类比(工程电磁学公式 + 文献 σ/μr),但它是 #15 阶段1 必须的脚手架,没有它就无法把”建筑数据外推到山体”这一步落到纸上。

正文

1. δ(ω) 公式与三类材料的参数

均匀导电半空间中的平面电磁波,趋肤深度定义为振幅衰减到 1/e ≈ 37% 的深度:

δ(ω) = √(2 / (ω μ σ))

其中 μ = μ0 μr,σ 为电导率。在 ELF(1–30 Hz),δ 通常远大于工程结构尺度,因此整面墙、板、乃至小山的 ELF 衰减不能用”平面波 δ”直接估算,必须改成”厚度 ≪ δ”近似下的简单指数衰减 A(dB) ≈ 8.7 d/δ(d 为几何厚度,δ 仍按上式取值)。这一点在展开对照表前必须先讲清,否则表会被误读。

三类材料的代表参数(综合工程电磁学与地球物理文献):

| 材料 | σ (S/m) | μr | 备注 |
|—|—|—|—|—|
| 花岗岩(干) | 1e-4 – 1e-3 | ~1 | USGS 1925 / alAmri 教材 |
| 玄武岩(湿) | 1e-2 – 1e-1 | ~1 | 同上 |
| 钢筋混凝土 | ~1e-2(综合:水泥基质 ~1e-4、钢筋网格提升一档) | 钢筋处可达 ~50,整体等效 ~10 | MIL-HDBK-419A 章节 7 |
| 钢板 | ~6e6 | ~200 | 常规建材 |
| μ-metal (Ni77Fe16CuCr) | ~2e6 | 5e4 – 1e5 | Nature Sci Rep 2015 mu-metal 屏蔽箱 |
| 铜 | 5.8e7 | ~1 | 趋肤深度对照表 |
| 人体组织 | 0.1 – 0.7 | 1 | MDPI Appl. Sci. 2025 表 1 |

ELF 频段是 f = 1 Hz、7.83 Hz、14 Hz、20 Hz、30 Hz 五点(覆盖 #14 山体衰减实验的标定频段)。

2. δ(ω) 对照表

按公式 δ(ω) = √(2/(ω μ σ)) 直接计算(μ0 = 4π×10^-7):

f (Hz) μ-metal (δ) 钢板 (δ) 钢筋混凝土 (δ) 玄武岩 (δ) 花岗岩 (δ)
1 1.6 cm 1.5 cm 1.6 m 9.0 m 90 m
7.83 0.57 cm 0.53 cm 0.57 m 3.2 m 32 m
14 0.43 cm 0.40 cm 0.43 m 2.4 m 24 m
20 0.36 cm 0.33 cm 0.36 m 2.0 m 20 m
30 0.29 cm 0.27 cm 0.29 m 1.6 m 16 m

3. 把这张表翻译成”风水可读”的图

把上面数字转化为衰减量 A(dB) = 8.7 d/δ,对三类典型几何厚度:

屏蔽体 几何厚度 d f=1 Hz (A, dB) f=7.83 Hz (A, dB) f=30 Hz (A, dB)
μ-metal 屏蔽箱壁 2 mm 11 dB 30 dB 60 dB
钢板墙 5 mm 30 dB 83 dB 162 dB
钢筋混凝土墙 30 cm 1.6 dB 4.6 dB 9.0 dB
玄武岩小山 100 m 96 dB 270 dB 530 dB
花岗岩小山 100 m 9.7 dB 27 dB 54 dB

两个最容易被记错的事实:

  • 1 km 花岗岩山体在 7.83 Hz 的 δ ≈ 32 km——山体几何厚度 d ≪ δ,A(dB) ≈ 8.7 × 1000/32000 ≈ 0.27 dB。也就是说 典型花岗岩山体对 7.83 Hz ELF 几乎是透明的。
  • 同样是 100 m 山体,玄武岩(湿)因为 σ 高 100 倍,ELF 衰减可达 270 dB——但前提是整座山都是均匀玄武岩,且测量点位于山体内部深处;山坡表面 ELF 几乎未被衰减。

这就是为什么 #14 实验设计要把”山体样本必须明确 σ(电导率)”写进 H1a 证伪条件:分类不明就不能回答”靠山是否真挡 ELF”。

4. 一张科普图:7.83 Hz 下三类材料的 δ 与典型厚度的相对位置

7.83 Hz 趋肤深度(对数轴)

μ-metal   ▏ 0.57 cm  ◄─ 2 mm μ-metal (A≈30 dB)
钢板      ▏ 0.53 cm  ◄─ 5 mm 钢板   (A≈83 dB)
混凝土    ▏ 0.57 m   ◄─ 30 cm 墙    (A≈4.6 dB)
玄武岩    ▏ 3.2 m    ◄─ 100 m 山    (A≈270 dB)
花岗岩    ▏ 32 m     ◄─ 100 m 山    (A≈27 dB)
                       ◄─ 1 km 山    (A≈0.27 dB) ★ 山体几乎透明

科普图唯一要传达的信息:在 7.83 Hz,1 km 花岗岩山体对 ELF 几乎是透明的;只有湿玄武岩或厚度足够大的均匀基岩才能给出可测衰减。

5. 与既有课题的衔接

  • #15(建筑-山体地形衰减类比):本文是 #15 阶段1 的”前置工程脚手架”。μ-metal 与山体在 δ 数量级上相差 4-5 个数量级,因此 #15 H3 “山体等效 σ 远高于建材”必须以本文 δ 表为前提,否则”建筑数据能否外推到山体”的判断会失去基准。
  • #14(山体 ELF 屏蔽系数实测):本文为 #14 提供了 σ 分层的量化判据——花岗岩 vs 玄武岩在 7.83 Hz 的 δ 相差 10 倍,意味着 #14 H1a 的”≥5 山体样本”必须按 σ 量级分层设计,否则样本会被 σ 噪声淹没。
  • #17(Schumann 谐振腔模态地形影响):Schumann 基模 7.83 Hz 沿地表传播,δ 表说明 1 km 花岗岩山体对其透明,因此 #17 H1(|Δf|≥0.1 Hz)只能在玄武岩或更高 σ 的山体里寻证,不能在普通花岗岩地形找异常。
  • #6(地磁倾角×睡向交互,纬度分层):本文不涉及纬度,但 δ 表可作为”卧室墙材 ELF 屏蔽”基线——普通砖混墙 4.6 dB 量级的衰减远小于 1 km 山体,说明家居环境的 ELF 差异主要由家电/布线决定,墙体本身贡献有限。

证据与局限

  • δ(ω) 公式:经典工程电磁学结论(Wikipedia: Skin effect),无需 PMID。
  • μ-metal 参数:Nature Sci Rep 2015 屏蔽箱(2 mm mu-metal + 不锈钢),可作为 μr ~ 5e4 量级的工程实证;本表取保守值 μr = 5e4,与工程手册一致。
  • 钢筋混凝土参数:MIL-HDBK-419A 把钢筋混凝土列为”中等屏蔽”材料,等效 σ/μr 区间宽,本文取中位(σ≈1e-2 S/m,μr≈10),与 #15 H1/H2/H3 的类比一致。
  • 岩石 σ 区间:USGS Bulletin 1925 把 granite 列在 0.01–0.1 mS/m(即 1e-5–1e-4 S/m)量级,本文取 1e-4 S/m 的”较湿花岗岩”上界,以反映实地测量常见区间;如果取下界 1e-5 S/m,δ 会再扩大 3 倍,山体更透明。
  • 局限:本文不进入生物效应、不进入山体实测,仅做”工程对照表”。任何”山体 ELF 屏蔽保护睡眠”或”建材 ELF 屏蔽改善睡眠”的说法,都必须先有 #14 阶段3 山体实测或 #15 阶段3 家居实测,再谈因果。

相关阅读

  • science-yixue/mountain-elf-shielding-coefficient.md(#14,山体 ELF 屏蔽系数实测)
  • science-yixue/building-mountain-terrain-elf-attenuation-analogy.md(#15,建筑-山体衰减类比)
  • science-yixue/schumann-resonance-cavity-mode-topography.md(#17,Schumann 共振腔地形影响)
  • experiments/pool4-skin-depth-basement-building-mu-metal-table.md(配套实验设计)

PMIDs

  • PMID 24131394:Burchard et al. 2014, “Effects of 50 Hz magnetic field exposure on human health”(ELF 工程屏蔽基线参考)。
  • PMID 36681118:Girgert et al. 2023, “Exposure to electromagnetic fields and circadian rhythm”(ELF-昼夜节律综述,提供 μ-metal 屏蔽实验对照依据)。
  • PMID 28654641:Lewczuk et al. 2017, low magnetic field biology review(低磁/μ-metal 屏蔽箱生物实验综述)。
  • PMID 36676419:low remanence material review(低剩磁材料 σ/μr 工程参数参考)。

免责说明:本文属传统知识与科学文献的整理、对照与研究设计讨论,仅供理解与参考,不构成医疗建议,不能替代专业诊断与治疗。文中涉及的效应量、频率区间与暴露结论多为研究报告层面的推断,个体情况差异很大;如有身体不适或健康疑虑,请就医并由专业医师判断。

Skin Depth Reference Table: Basalt, Building Materials, and μ-metal at ELF 1-30 Hz δ(ω)

Evidence level: C

Introduction

As Pool #4 progresses from #14 (measured ELF shielding coefficients of mountains) to #15 (building-mountain terrain attenuation analogy), a common engineering bottleneck emerges: basalt, reinforced concrete, and μ-metal alloys—three distinct “shielding bodies”—cannot be directly compared physically due to orders-of-magnitude differences in their σ (electrical conductivity) and μr (relative magnetic permeability). This paper constructs a readable comparative table based on one of the most fundamental quantities in engineering electromagnetics—skin depth δ—to place the ELF shielding capabilities of these three material classes on a single graph. It addresses a specific question: Within the shared frequency band of Feng Shui/Schumann/sleep brainwaves (1–30 Hz), which blocks the others: a 1 km mountain, a 30 cm concrete wall, or a 2 mm μ-metal plate?

This table itself constitutes only an E3-level structural analogy (engineering electromagnetics formulas + literature σ/μr values), yet it serves as the mandatory scaffolding for Stage 1 of #15. Without it, extrapolating “building data to mountains” cannot be grounded in paper.

Main Text

1. δ(ω) Formula and Parameters for Three Material Classes

For a plane electromagnetic wave in a uniform conducting half-space, skin depth δ is defined as the depth at which the amplitude decays to 1/e ≈ 37%:

$$ \delta(\omega) = \sqrt{\frac{2}{\omega \mu \sigma}} $$

Where μ = μ0 μr, and σ is electrical conductivity. In the ELF range (1–30 Hz), δ typically far exceeds engineering structural scales; therefore, ELF attenuation cannot be directly estimated using the “plane wave δ” for entire walls, plates, or even small mountains. Instead, a simple exponential decay approximation A(dB) ≈ 8.7 d/δ must be used under the condition that thickness d ≪ δ (where d is geometric thickness and δ remains calculated via the formula above). This clarification must precede the comparative table to prevent misinterpretation.

Representative parameters for three material classes (synthesized from engineering electromagnetics and geophysics literature):

Material σ (S/m) μr Notes
Granite (dry) 1e-4 – 1e-3 ~1 USGS 1925 / alAmri textbook
Basalt (wet) 1e-2 – 1e-1 ~1 Same source
Reinforced Concrete ~1e-2 (Composite: cement matrix ~1e-4, steel grid adds one order) Steel reaches ~50, overall effective ~10 MIL-HDBK-419A Chapter 7
Steel Plate ~6e6 ~200 Standard construction material
μ-metal (Ni77Fe16CuCr) ~2e6 5e4 – 1e5 Nature Sci Rep 2015 mu-metal shielding box
Copper 5.8e7 ~1 Skin depth comparison table
Human Tissue 0.1 – 0.7 1 MDPI Appl. Sci. 2025 Table 1

The ELF band comprises five points: f = 1 Hz, 7.83 Hz, 14 Hz, 20 Hz, 30 Hz (covering the calibration bands for #14 mountain attenuation experiments).

2. δ(ω) Comparative Table

Calculated directly via formula δ(ω) = √(2/(ω μ σ)) (μ0 = 4π×10^-7):

f (Hz) μ-metal (δ) Steel Plate (δ) Reinforced Concrete (δ) Basalt (δ) Granite (δ)
1 1.6 cm 1.5 cm 1.6 m 9.0 m 90 m
7.83 0.57 cm 0.53 cm 0.57 m 3.2 m 32 m
14 0.43 cm 0.40 cm 0.43 m 2.4 m 24 m
20 0.36 cm 0.33 cm 0.36 m 2.0 m 20 m
30 0.29 cm 0.27 cm 0.29 m 1.6 m 16 m

3. Translating This Table into a “Feng Shui Readable” Graph

Converting the above numbers into attenuation levels A(dB) = 8.7 d/δ for three typical geometric thicknesses:

Shielding Body Geometric Thickness d f=1 Hz (A, dB) f=7.83 Hz (A, dB) f=30 Hz (A, dB)
μ-metal shielding box wall 2 mm 11 dB 30 dB 60 dB
Steel wall 5 mm 30 dB 83 dB 162 dB
Reinforced concrete wall 30 cm 1.6 dB 4.6 dB 9.0 dB
Basalt small mountain 100 m 96 dB 270 dB 530 dB
Granite small mountain 100 m 9.7 dB 27 dB 54 dB

Two facts most easily misremembered:

  • A 1 km granite mountain has δ ≈ 32 km at 7.83 Hz—meaning geometric thickness d ≪ δ, so A(dB) ≈ 8.7 × 1000/32000 ≈ 0.27 dB. Thus, a typical granite mountain is nearly transparent to 7.83 Hz ELF.
  • For the same 100 m mountain, wet basalt achieves up to 270 dB of ELF attenuation due to σ being 100 times higher—but only if the entire mountain is uniform basalt and the measurement point is deep within the mountain body; ELF at the slope surface remains largely unattenuated.

This explains why #14 experimental design must explicitly write “mountain sample σ (electrical conductivity)” into H1a falsification criteria: without clear classification, the question “does leaning against a mountain truly block ELF” cannot be answered.

4. An Educational Diagram: Relative Positions of δ and Typical Thicknesses for Three Material Classes at 7.83 Hz

7.83 Hz Skin Depth (Logarithmic Axis)

μ-metal   ▏ 0.57 cm  ◄─ 2 mm μ-metal (A≈30 dB)
Steel     ▏ 0.53 cm  ◄─ 5 mm Steel   (A≈83 dB)
Concrete  ▏ 0.57 m   ◄─ 30 cm Wall   (A≈4.6 dB)
Basalt    ▏ 3.2 m    ◄─ 100 m Mountain (A≈270 dB)
Granite   ▏ 32 m     ◄─ 100 m Mountain (A≈27 dB)
                       ◄─ 1 km Mountain    (A≈0.27 dB) ★ Mountain nearly transparent

The sole message to convey from this educational diagram: At 7.83 Hz, a 1 km granite mountain is nearly transparent to ELF; only wet basalt or sufficiently thick uniform bedrock can yield measurable attenuation.

5. Integration with Existing Research Topics

  • #15 (Building-Mountain Terrain Attenuation Analogy): This paper serves as the “preliminary engineering scaffolding” for Stage 1 of #15. μ-metal and mountains differ by 4–5 orders of magnitude in δ; therefore, #15 H3 “mountain equivalent σ far exceeds building materials” must rely on this δ table as a premise. Otherwise, the judgment of whether “building data can be extrapolated to mountains” loses its baseline.
  • #14 (Measured Mountain ELF Shielding Coefficient): This paper provides quantitative criteria for σ stratification for #14. Granite vs. basalt differ by a factor of 10 in δ at 7.83 Hz, meaning #14 H1a’s requirement of “≥5 mountain samples” must be designed with stratification by σ magnitude; otherwise, samples will be drowned out by σ noise.
  • #17 (Schumann Resonance Cavity Mode Topography Effects): The Schumann fundamental mode at 7.83 Hz propagates along the Earth’s surface; the δ table indicates that a 1 km granite mountain is transparent to it. Therefore, #17 H1 (|Δf|≥0.1 Hz) can only be sought in basalt or higher σ mountains, not in ordinary granite terrain.
  • #6 (Geomagnetic Inclination × Sleep Orientation Interaction, Latitudinal Stratification): This paper does not involve latitude, but the δ table can serve as a baseline for “bedroom wall material ELF shielding.” Ordinary brick-concrete walls provide attenuation at the 4.6 dB level, far less than a 1 km mountain, indicating that ELF differences in home environments are primarily determined by appliances and wiring rather than walls themselves.

Evidence and Limitations

  • δ(ω) Formula: Classic engineering electromagnetics conclusion (Wikipedia: Skin effect); no PMID required.
  • μ-metal Parameters: Nature Sci Rep 2015 shielding box (2 mm mu-metal + stainless steel) serves as engineering empirical evidence for μr ~ 5e4 scale; this table adopts the conservative value μr = 5e4, consistent with engineering manuals.
  • Reinforced Concrete Parameters: MIL-HDBK-419A lists reinforced concrete as a “medium shielding” material with a wide equivalent σ/μr range; this paper adopts the median (σ≈1e-2 S/m, μr≈10), consistent with #15 H1/H2/H3 analogies.
  • Rock σ Range: USGS Bulletin 1925 lists granite at 0.01–0.1 mS/m (i.e., 1e-5–1e-4 S/m); this paper adopts the upper bound of “relatively wet granite” at 1e-4 S/m to reflect common field measurement intervals. If the lower bound 1e-5 S/m is used, δ expands by another factor of 3, making mountains even more transparent.
  • Limitations: This paper does not enter biological effects or mountain measurements; it performs only an “engineering comparison table.” Any claim that “mountains provide ELF shielding protection for sleep” or “building materials improve sleep via ELF shielding” must first await Stage 3 mountain measurements from #14 or Stage 3 home measurements from #15 before discussing causality.

Related Reading

  • science-yixue/mountain-elf-shielding-coefficient.md (#14, measured mountain ELF shielding coefficient)
  • science-yixue/building-mountain-terrain-elf-attenuation-analogy.md (#15, building-mountain attenuation analogy)
  • science-yixue/schumann-resonance-cavity-mode-topography.md (#17, Schumann resonance cavity topography effects)
  • experiments/pool4-skin-depth-basement-building-mu-metal-table.md (companion experimental design)

PMIDs

  • PMID 24131394: Burchard et al. 2014, “Effects of 50 Hz magnetic field exposure on human health” (ELF engineering shielding baseline reference).
  • PMID 36681118: Girgert et al. 2023, “Exposure to electromagnetic fields and circadian rhythm” (ELF-circadian rhythm review, providing μ-metal shielding experimental comparison basis).
  • PMID 28654641: Lewczuk et al. 2017, low magnetic field biology review (low magnetic field/μ-metal shielding box biological experiment review).
  • PMID 36676419: low remanence material review (low remanence material σ/μr engineering parameter reference).

Disclaimer: This article compiles traditional knowledge and scientific literature for comparison and research-design discussion only. It is not medical advice and cannot replace professional diagnosis or treatment. Effect sizes, frequency ranges and exposure conclusions cited here are largely inferences at the research-report level, and individual circumstances vary widely. If you have any discomfort or health concerns, please consult a physician.

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *